HITACHI RAS 20 FS,давление в норме,при включение даёт ошибку F21.
Что означает эта ошибка и какая зависимость давление/напряжение каждого пресостата?
А может и мануал найдется?
mg14,спасибо болшое,сегодня заменили датчика высокого давления(у родного напряжение на выходе было 6 вольт а у нового 1,6 вольт в покое) и всё заработало.
Option error(option wasn’t set up or option data error)
Set up the Model Option
MODEL___OPTION CODE
SH12ZSG__066025-172362
SH09ZS8__027064-17221d
SH07ZS8__026064-1720Fb
8-5. Set up the Model Option
Step 1 : Preparing the remocon to main PBA option set
1st Remove the battery from the remocon.
2nd Press the temperature raise/down button simultaneously and insert the battery again.
3rd Make sure the remocon display shown as 00 00 00
Step 2 : Second stage preparation of the remocon option set.
. Note ; In case the wrong letter has been selected, continue to press the button until the correct letter appears.
1st If the first stage number “0” appears on the display, proceed to the second stage.
2nd Every time the "1" and "7" button, “0 ” and “1 ” each continue to appear.
3rd Whenever pressing the 2, 3, 4, 5, 6, 8, 9 , 10 , 11, 12 button, the number increases from
0~9(0123456789) and A, b, C, d, E, F each time.
1 If the first number is 0 , it is correct otherwise press "Mode" until 0 appear.
2 When pressing the "UP" button 0 ~ F appear on the display,select one of them.
3 When pressing the "DOUN" button 0 ~ F appear on the display,select one of them.
4 When pressing the "FAN" button 0 ~ F appear on the display,select one of them.
5 When pressing the "Off Timer"button0 ~ F appear on the display,select one of them.
6 When pressing the "ON/OFF"button 0 ~ F appear on the display,select one of them.
1 If the first number is 1, it is correct otherwise press "Mode" until 1 appear.
2 When pressing the "UP" button 0 ~ F appear on the display, select one of them.
3 When pressing the "DOUN" button 0 ~ F appear on the display, select one of them.
4 When pressing the "FAN" button 0 ~ F appear on the display, select one of them.
5 When pressing the "Off Timer" button 0 ~ F appear on the display, select one of them.
6 When pressing the "ON/OFF" button 0 ~ F appear on the display, select one of them.
Step 3 : Reconfirming option set after completion (in case of ex. 066025-172362)
After pressing "Mode" selector for the 0 mode, the display shown as 066025.
After pressing "Mode" selector for the 1 mode, the display shown as 172362.
Step 4 : Pressing the ON/OFF button
When pressing the operation ON/OFF key with the direction of remote controller for unit, the sound “Ding” or “Diriring” is
heard and the OPERATION LED lamp is flickering at the same time, then the input of option is completed.
(If the diriring sound isn’t heard, try again pressing the ON/OFF button.)
Step 5 : Unit operation test-run
First, Remove the battery from the remote controller.
Second, Re-insert the battery into the remote controller.
Third, Press ON/OFF key with the direction of remote controller for set.
Error Mode :
1st If all lamps of indoor unit are flickering, Plug out and plug in again and pressing ON/OFF key to retry.
2nd If the unit is not working properly or all lamps are continuously flickering after setting the option code, see
if the correct option code is set up for it’s model.
У меня такое было только два раза:
1.чип кондер на выходе ИК приёмника коротил
2.в больнице-бактерицидные лампы с импульсным питанием излучали на той же частоте,как и пульт
1st Take out the batteries of remote control.
2nd Press the temperature(doun&up) button simultaneously and insert the battery again.
3rd Make sure the remocon display shown as (самое верхнее) .
Setting Option SEG1
Push the "doun" button to set the display panel to "2"
Setting Option SEG2
Push the "up" button to set the display panel to "5"
Change it into the set display of Option SEG3 and SEG4 with the button
Setting Option SEG3
Push the "doun" button to set the display panel to "0"
Setting Option SEG4.
Push the "up" button to set the display panel to "2"
Change it into the set display of Option SEG5 and SEG6 with the button
...............
...............
Форум